This polished Marble tiled floor was installed in a house in the old market town of Petersfield. The tile and grout was in good condition but like all polished stone floors they will go dull after a period of time and require burnishing and polishing to restore shine.
Cleaning Marble Floor Tiles
We gave the floor a quick sweep and wash down with a dilution of Tile Doctor Pro-Clean partly to ensure any surface grit etc. was removed but also so we could get a stiff grout brush in along the grout lines and give them a clean. Once done the floor was rinsed down with water which was removed with a wet vacuum, once done we moved straight onto burnishing the floor to restore the polish. Burnishing requires the application of a little water so there was no need to wait for it to dry.
Burnishing requires the application of four different diamond encrusted graded pads in sequence working from coarse which removed old sealers and dirt through to medium, fine and super fine pads which build up the polish on the floor. The floor requires a rinse in-between each pad to remove any slurry and water is extracted from the floor using the wet vacuum, after the super fine pad we removed as much water from the floor as possible and left it to dry overnight ready for sealing the next day.
Sealing Marble Floor Tiles
On our return the next day we made sure the floor was dry with the use of a damp meter and once we were happy we sealed the Marble tiles using two coats of Tile Doctor Colour Grow which is an impregnating sealer the occupied the pores in the tile to prevent other contaminates soaking into the tile. It also does a nice job of lifting the natural colours in the stone and enhancing the look of the tile.
This Milled Sandstone tiled floor was installed in the kitchen of a house in the village of Warsash on the south coast. The floor was looking washed out and lost most of its colour and the owner wanted it looking its best.
Cleaning a Sandstone Tiled Floor
The first job was to remove the kick boards from around base of the kitchen units a followed by the application of Tile Doctor Pro-Clean diluted with 10 parts warm water. This was left to soak into the stone and then worked in using a black scrubbing pad. This action gave the floor a good clean and the now dirty cleaning solution was removed using a wet vacuum, the floor was rinsed down with water and the process repeated in the areas where further attention was required until we were happy the tiles were clean. The final cleaning action was to wash down the tiles with clean water a final time to remove any cleaning product and neutralise the floor before the next step of sealing. The wet vacuum was used again to remove as much water from the floor as possible and we then left for the evening so the floor could fully dry overnight.
Sealing a Sandstone Tiled Floor
We came back the next day and tested the floor with a damp meter in a few different locations to make sure no dampness remained in the stone. The sandstone was dry so we proceeded to seal the floor with Tile Doctor Colour Grow which is an impregnating sealer that occupies the pores in the stone preventing dirt from becoming ingrained there, it also as its name suggests brings out the colour in the stone and it certainly worked well on this floor and brought out the brown colours of the Sandstone, two coats were sufficient.
Milled Sandstone Floor Cleaned and Sealed in Hampshire
This was a straightforward request to deep clean the Ceramic Tile and Grout in the kitchen of a house in Romsey, Hampshire but as you will see from the photograph below the Grout was far too stained to be cleaned effectively. Kitchen grout gets a lot of abuse from spillages so this is not unusual and to prevent it the grout can be sealed or you can choose a dark grout colour.
Cleaning and Preparing the Tile and Grout
To get the tile and grout clean I applied a dilution of Tile Doctor Pro-Clean and left it to soak in to the surface dirt for a while before scrubbing it with a rotary machine fitted with a black scrubbing pad and also a stiff hand brush along the grout lines. This was then washed down with warm water all of which was removed by a wet Vacuum. This cleaning process was repeated until the tiles were clean and the grout was a good as I could get it. Unfortunately the grout had stained quite badly and we were unable to get a good uniform appearance so after discussing this with the customer it was agreed that we would apply a white Grout Colourant.
Applying Grout Colourant
If it was a small area I could have considered using a Grout Pen however this required more than a touch up so this is where you need an epoxy grout colourant which forms a hard wearing epoxy barrier over the existing grout that looks natural and effectively protects the grout from further staining.
The grout needs to be clean and dry before you apply it so if you’re doing this from scratch make sure you clean the grout first with Pro-Clean or the Pre-Treater product that is available. The grout colourant is then easily applied using a toothbrush, it sounds easy but you have to be very methodical. The colourant dries in about an hour after which it’s worth double checking your work and then removing any excess by applying a little water and running over it with a white pad.
I think you will agree from the photographs the tiles look much cleaner and the floor transformed by the improvement in grout colour.
These slate tiles were installed in the back kitchen of a house in the seaside resort town of Bognor Regis, they were in good physical condition but unfortunately any sealer had worn off some time ago causing them to lose their appearance and look faded.
Cleaning Slate Tiled Floors
Dirt had become ingrained into the tile so I went straight for a powerful cleaning combination of Tile Doctor Pro-Clean Tile and Grout cleaner mixed 50:50 with NanoTech UltraClean. The UltraClean adds tiny abrasive particles to the Pro-Clean making it a more effective cleaning product. The solution was left to dwell on the floor for a while before being scrubbed into the tiles with a rotary machine fitted with a black scrubbing pad; as usual a stiff hand brush was used along the grout lines to get them clean.
The soiled solution was removed using a wet vacuum and floor thoroughly rinsed down with clean water. Pro-Clean works as a stripper as well as a cleaner and so any remaining sealer was also removed in the process.
Sealing Slate Floor Tiles
This process took a day so the floor was left to dry overnight and we came back the next day to seal it with five coats of Tile Doctor Seal and Go which is the ideal sealer for Slate tiles as it provides good stain protection with leaves a nice sheen finish; Seal and Go is also water based so there’s no smell like you get with other sealers.
The slate tiles now look 100% improved and the sealer should keep them that way for two to three years depending on floor traffic.
Cleaning and Sealing a Slate Kitchen Tiles in Hampshire